Epson All models error codes
Codes
- *Error codeMotor Driver uses different parts depending on manipulator models. Refer to the next page for Motor Driver selectionMedium
- 0000Error codeCR PID sürüş süresiMedium
- 0xError code0xE1Medium
- 1Error codeAC Servo Motor (50 W)Medium
- 2Error codeSuitable cord (Length about 800 mm)Medium
- 3Error code■ Do not remove the connector sub plate forcibly. Removing the connector sub plate forcibly may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. ■ When installing the connector sub plate, be careful not to allow the cables to interfere with the plate mounting and do not bend these cables forcibly to push them into the cover. Unnecessary strain on cables may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. When routing the cables, observe the cable locations after removing the connector sub plate. Be sure to place the cables back to their original locationsMedium
- 4Error code■ Do not remove the connector plate forcibly. Removing the connector plate forcibly may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. ■ When installing the connector plate, be careful not to allow the cables to interfere with the plate mounting and do not bend these cables forcibly to push them into the cover. Unnecessary strain on cables may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. When routing the cables, observe the cable locations after removing the connector plate. Be sure to place the cables back to their original locationsMedium
- 5Error code■ Do not remove the connector sub plate forcibly. Removing the connector sub plate forcibly may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. ■ When installing the connector sub plate, be careful not to allow the cables to interfere with the plate mounting and do not bend these cables forcibly to push them into the cover. Unnecessary strain on cables may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. When routing the cables, observe the cable locations after removing the connector sub plate. Be sure to place the cables back to their original locationsMedium
- 7Error codeFour digitsMedium
- 30Error codeThis is usually caused by a program input errorMedium
- 33Error codeThis error occurs when large amounts of data are being transmittedMedium
- 34Error codeThis error occurs when the transmission is affected by line noise or other interference. Determine the cause of the interference (such as an extra-long cable or a crimped cable, or a nearby noise-generating device) then retry the transmissionMedium
- 0300Error codePE detector errorMedium
- 0310Error codeHead Hot - baskı öncesiMedium
- 0330Error codeDiğer mürekkep aygıtı hatasıMedium
- 0340Error codeHome position errorMedium
- 400WError codeMaintenance partsMedium
- 0479Error code"Sistem Hatası" (genel kapsamlı)Low
- 627Error codeSuitable cord (Length about 800 mm)Medium
- 750Error codeMaintenance partsMedium
- 1000Error codeADF PID aşırı hızMedium
- 1042Error codeKoruma kapağı (safeguard) açıkken çalıştırılamazMedium
- 1043Error codeHata durumu varken çalıştırılamazMedium
- 1048Error codeDüşük gerilim algılandıktan sonra çalıştırılamazHigh
- 1123Error codeDosya hatası. I/O etiket dosyası bozukMedium
- 1126Error codeDosya hatası. Yazılım opsiyon bilgisi bozukMedium
- 1150Error codeDosya hatası. Hata geçmişi geçersizMedium
- 1200Error codeDerleme hatası, derleme mesajını kontrol edinLow
- 1201Error codeBağlama (link) hatası, link mesajını kontrol edinLow
- 1514Error codeMaintenance partsMedium
- 2030Error codePanel Unit arızasıMedium
- 2051Error codeCard Board arızasıMedium
- 2229Error codeDC (PROPELLER TYPE) FANMedium
- A3Error codeFailure in firmware updatingMedium
- A3957SError codeIC4,5Medium
- A6627SError codeIC6Medium
- A6628SError codeIC7/IC13Medium
- age142Error codeCR motor assembly (517) (Page 168)Medium
- age165Error codeConnection failure between the auto cutter unit and the main circuit board unitMedium
- B0HError codeApplication errorMedium
- B8Error codeAbnormal ResponseMedium
- C3500Error codePower supplyHigh
- CN1Error codeCN1 or CN2 on the CCD sensor board is disconnectedMedium
- CN3Error codeTo the CR MotorMedium
- CN15Error codeCR motor assembly (517)Medium
- CN16Error codePressure pump motorMedium
- CN17Error codePF motor IS pump unit motorMedium
- CN20Error codeCutter motorMedium
- CN21Error codeSuction fan (507)Medium
- CN29Error codePressure pump unit (551)Medium